Jandy | R0688600 | Variable Speed Drive 2.2 to 2.7 HP, Gen-II Non-SVRS, Drive Only, Fits VS PlusHP, VS FloPro and ePump
Couldn't load pickup availability
The Jandy R0688600 Variable Speed Drive is the genuine OEM drive module for Gen-II permanent magnet variable speed pumps in the 2.2 to 2.7 HP class. The drive is the electronics package that sits on top of the motor. It converts single phase input power into the variable frequency output the motor runs on, and it holds the speed control logic, the schedule memory and the keypad.
Drive Only, Not a Motor
This part replaces the drive electronics only. If the motor has seized or burned out, order the complete motor and drive assembly, R0562201, instead. The R0688600 is also Non-SVRS and Gen-II specific. It does not fit SVRS pump variants or earlier drive generations.
Compatible Pumps
- VS PlusHP: VSPHP270JEP, VSPHP270AUT
- VS FloPro: VS-FHP2.0, VSFHP270JEP, VSFHP270AUT
- ePump: VSSHP220AUT, VSSHP270AUT
When You Need This Part
A failed drive is the most common reason a Jandy variable speed pump stops running while the motor is still good. Typical signs are a pump that will not power up, a blank or frozen keypad, fault codes that come back after a power cycle, or a pump that hums but never reaches speed. A new drive costs a fraction of a new pump.
Key Features
- Genuine Jandy OEM: correct firmware and connector layout for the Gen-II motor.
- Restores full control: variable speed operation, onboard scheduling and keypad programming all come back with the new drive.
- Component level repair: replace the electronics, keep the pump.
- Covers three pump families: VS PlusHP, VS FloPro and ePump in the 2.2 to 2.7 HP class.
- Gen-II permanent magnet design: matched to the ECM motor it drives.
Specifications
- Part Number: R0688600
- UPC: 052337071161
- Type: Variable frequency drive module, drive only
- Horsepower Class: 2.2 to 2.7 HP
- Generation: Gen-II
- SVRS: Non-SVRS
- Complete Motor and Drive Assembly: R0562201
- Alternate Part Numbers: TLD-101-7241, JDYR0688600, JNDR0688600
- Brand: Jandy / Zodiac
Frequently Asked Questions
Does this include the motor?
No. This is the drive module only. If your motor has failed, order the complete motor and drive assembly R0562201.
How do I tell a failed drive from a failed motor?
A drive fault usually shows as a dead or frozen display, a pump that will not start, or fault codes that survive a power cycle while the motor spins freely by hand. A failed motor more often tries to start and trips the breaker, or the shaft will not turn. A pool professional can confirm with a resistance check on the motor windings.
Will this fit an SVRS pump?
No. SVRS pumps use a different drive and the two are not interchangeable.
Will it fit a Gen-I pump?
No. This drive is Gen-II only. Check the generation on your pump or motor label before ordering.
Do my saved schedules carry over?
No. Schedules and speed presets live in the drive, so a new drive arrives at factory defaults. Write down your speeds and run times before removing the old drive if the display still works.
How do I confirm it fits my pump?
Match the part number on the drive you are replacing, or check the parts list for your pump model. If your model is not listed on this page, send it to us before you order and we will confirm the fit.
Who should install it?
A qualified pool professional or licensed electrician. Cut power at the breaker before opening the drive, and remember that permanent magnet motors can generate voltage while the shaft is turning.
What is the warranty?
Standard Jandy manufacturer warranty. On some equipment coverage applies only when a licensed professional performs the installation. Keep your receipt and packaging until you have confirmed correct operation.
California Proposition 65 Warning: This product can expose you to chemicals known to the State of California to cause cancer and reproductive harm. For more information go to www.P65Warnings.ca.gov.